CATÁLOGOCategorías
categorias
RC4WD 1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed
  • RC4WD 1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed

RC4WD 1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed

2.201,95 €
Impuestos incluidos

RC4WD 1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed

Cantidad
Disponible bajo pedido, consultar disponibilidad.

1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed


Notice: This product is for experienced RC hobbyists. This is not recommended for anyone under the age of 16. 
Specifications:
  • Hard Plastic European Style Front Cab
  • Full Metal 2 Speed Transmission (Planetary Gears)
  • Transfer Case (Billet Aluminum)
  • Scale Fuel Tank (Billet Aluminum)
  • Super Scaled Leaf Spring Suspension Setup
  • Scale Rims (Billet Aluminum)
  • Remote Lockable Front and Rear Axles (Locking Differential)
  • Full Metal Front and Rear Axle Housing
  • Steel Scale Drive Shaft
  • Realistic Front Cab Latch
  • LiPo Cutoff
  • Molded Functional Fuel Tank
  • Rear Light Guards
  • Scale Light Buckets (Fits 3-5mm LED)
  • Recommended Payload: 10kg / 22lbs
  • Painted Body
  • Scale Wheels and Tires
  • Brushed Motor
  • Maximum Lift Power: 42kg / 92lbs
  • 930KV Brushless Motor-Driven Micro Hydraulic Pump
  • Spare Tire Included
  • Automatic Trailer Gate (Do Not Attempt to Open by Hand)
  • Length: 25.1in / 638mm
  • Width: 9.05in / 230mm
  • Height: 10.7in / 273mm (Including Antenna)
  • Weight: 6.8kg / 14.9lbs
  • Axle Gear Ratio: 2.6 : 1
  • Maximum Load: 15kg / 33lbs
  • First Gear 1:64, Second Gear 1:16 (Transmission)
  • Basic 6 Channel 2.4Ghz Radio
What's Included:
  • 1x 1/14 4X4 Overland Hydraulic RTR Truck w/Utility Bed
Required Parts:
Instruction Manual:
Notes:
  • When raising the dump bed, do not leave at upper-most position for more than 2 seconds, doing so may cause damage to the hydraulic system.
  • Do not push/pull the truck by the tailgate, doing so may cause damage to the locking mechanism.
  • Do not use more than 3S battery. (11.1 volt(s))
  • Do not try to operate lift past its fully-extended height, doing so may cause damage to hydraulic system.
  • Must turn on the transmitter before starting the ESC.
  • ESC Supports XT60 Connector
  • While some components may come assembled, we recommend checking the hardware and screws are all properly secure, especially after shipping. As an option, you may want to apply thread lock to some of the installed hardware.
  • Use good quality hex drivers to avoid stripping screw heads.
  • Use thread lock when putting metal screws into metal parts.
  • Steps marked with an asterisk (*) require threadlock.
  • Use threadlock sparingly.
  • Do not over tighten screws, or you may strip the thread.
  • This product is for experienced R/C users. Not recommended for beginners.
  • The axle hubs can be removed, but may require additional force.
  • This Product Is Professionally Pre-assembled
  • Manufactured by JDCustoms 30 Days Limited Warranty

RC4VVJD00065